Difference between revisions of "OSBYTE &03"
m (1 revision) |
(Added list of common settings.) |
||
| Line 1: | Line 1: | ||
[[Category:OSBYTE]] | [[Category:OSBYTE]] | ||
| − | |||
| − | |||
OSBYTE &03 (3) - Select output device | OSBYTE &03 (3) - Select output device | ||
| − | On entry, | + | On entry, X=new output selection |
| − | X=new output selection | ||
On exit, X=old output selection | On exit, X=old output selection | ||
| − | Controls which output device or devices receive the characters sent to [[OSWRCH]] | + | Controls which output device or devices receive the characters sent to [[OSWRCH]]. |
The value of X is made up as follows: | The value of X is made up as follows: | ||
| − | |||
{| class="wikitable" | {| class="wikitable" | ||
! Bit !! Meaning if set | ! Bit !! Meaning if set | ||
| Line 33: | Line 29: | ||
|} | |} | ||
| + | This flowchart shows the flow of characters from the OSWRCH entry point to the output devices. | ||
| + | [[Image:OSWRCH output fanout.png|Flowchart of pathways from the OSWRCH entry point to the output devices]] | ||
| + | |||
| + | |||
| + | Common OSBYTE 3 settings are: | ||
| + | {| class="wikitable" | ||
| + | | *FX3,0 || normal state, serial disabled, VDU enabled, printer enabled by VDU 2, spool output if *SPOOL file open | ||
| + | |- | ||
| + | | *FX3,1 || normal output, also send to serial port | ||
| + | |- | ||
| + | | *FX3,2 || disable all output except printer port and any *SPOOL file | ||
| + | |- | ||
| + | | *FX3,3 || disable VDU, enable serial port and any *SPOOL file | ||
| + | |- | ||
| + | | *FX3,16 || normal output without copying to *SPOOL file | ||
| + | |- | ||
| + | | *FX3,18 ||disable all output except printer port | ||
| + | |- | ||
| + | | *FX3,23 || disable all output except serial port | ||
| + | |- | ||
| + | | *FX3,86 || disable all output entirely | ||
| + | |} | ||
-- [[User:Beardo|beardo]] 21:43, 5 October 2007 (BST) | -- [[User:Beardo|beardo]] 21:43, 5 October 2007 (BST) | ||
| + | [[User:Jgharston|Jgharston]] ([[User talk:Jgharston|talk]]) 01:42, 25 December 2016 (UTC) | ||
Revision as of 03:42, 25 December 2016
OSBYTE &03 (3) - Select output device
On entry, X=new output selection
On exit, X=old output selection
Controls which output device or devices receive the characters sent to OSWRCH.
The value of X is made up as follows:
| Bit | Meaning if set |
|---|---|
| 0 | Enable serial port |
| 1 | Disable screen drivers (overrides VDU 2 and VDU 6)
|
| 2 | Disable printer (overrides VDU 2 and bits 3 and 6)
|
| 3 | Enable printer (overrides VDU 3)
|
| 4 | Disable output to *SPOOL file
|
| 5 | Not used |
| 6 | Disable printer except for VDU 1 sequences (overrides bit 3)
|
| 7 | Not used |
This flowchart shows the flow of characters from the OSWRCH entry point to the output devices.
Common OSBYTE 3 settings are:
| *FX3,0 | normal state, serial disabled, VDU enabled, printer enabled by VDU 2, spool output if *SPOOL file open |
| *FX3,1 | normal output, also send to serial port |
| *FX3,2 | disable all output except printer port and any *SPOOL file |
| *FX3,3 | disable VDU, enable serial port and any *SPOOL file |
| *FX3,16 | normal output without copying to *SPOOL file |
| *FX3,18 | disable all output except printer port |
| *FX3,23 | disable all output except serial port |
| *FX3,86 | disable all output entirely |
-- beardo 21:43, 5 October 2007 (BST) Jgharston (talk) 01:42, 25 December 2016 (UTC)
