Difference between revisions of "OSWORD &62"
m (moved OSWORD 62 to OSWORD &62) |
m |
||
| Line 1: | Line 1: | ||
[[Category:OSWORD]] | [[Category:OSWORD]] | ||
| − | OSWORD &62 (98 ) - Access LVROM controller | + | OSWORD &62 (98 ) - Access LVROM controller |
| + | __TOC__ | ||
| + | ==Specification== | ||
| + | Same format as ADFS call &72 (114) | ||
| + | On entry: | ||
| + | XY?0 = 0, returned result | ||
| + | XY!1 = data address | ||
| + | XY?5 = command | ||
| + | XY?6 = drive number in b5-b7, sector b16-b20 in b0-b4 | ||
| + | XY?7 = sector number b8-b15 | ||
| + | XY?8 = sector number b0-b7 | ||
| + | XY?9 = number of sectors or 0 | ||
| + | XY?10 = 0 | ||
| + | XY!11 = data length if X%?9=0 | ||
| + | This is a standard SCSI command block. The drive number in XY?6 is ORed with | ||
| + | the current drive. If VFS is not selected when the call is made, VFS is | ||
| + | selected. Consequently, any code that calls OSWORD &62 must remember the | ||
| + | current filing system and restore it afterwards. In practice it is easier | ||
| + | to select VFS before calling OSWORD &62. | ||
| − | + | ===Commands=== | |
| − | + | &00=Test drive ready | |
| − | + | &01=Seek track 0 | |
| − | + | &03=Request status | |
| − | + | &08=Read data | |
| − | + | &0B=Seek track | |
| − | + | &1B=Stop/Start drive; stop if XY?9=0, start if XY?9=1 | |
| − | + | &C8=Read F-code result from LVDOS | |
| − | + | &CA=Transmit F-code to LVDOS | |
| − | + | ||
| − | + | ===Results=== | |
| − | + | &00=Ok | |
| + | &02=Drive door open | ||
| + | &03=Media error, eg disk dirty | ||
| + | &05=Bad SCSI command | ||
| + | &04=Not ready | ||
| + | &40=Write protected | ||
| + | &48=CRC error | ||
| + | &50=Sector not found | ||
| + | &60=Bad command | ||
| + | &61=Bad address | ||
| + | &63=Volume error | ||
| + | &65=Bad drive | ||
| + | &6F=Abort | ||
| + | |||
| + | The result byte can be preloaded with a value to return if no OSWORD &62 | ||
| + | routine exists. For instance, preloading the result with &00 makes all such | ||
| + | failed calls appear to succeed, preloading with &50 makes all calls appear | ||
| + | to return 'Sector not found'. | ||
| + | |||
| + | ===Coding=== | ||
| + | The following routine can be used to perform an OSWORD &62 call. It requires | ||
| + | X%=>15-byte control block, Y%=X%DIV256. | ||
| + | |||
| + | DEFFNlvfs(cmd%,addr%,num%,sect%,drv%):LOCALfs% | ||
| + | fs%=FNfs:IFfs%<>10:*FX143,18,10 | ||
| + | X%?0=0:X%!1=addr%:X%?5=cmd%:X%?6=drv%*32+((sect%AND&1F0000)DIV65536) | ||
| + | X%?7=((sect%AND&FF00)DIV256):X%?8=sect%:X%!9=0:X%!11=num% | ||
| + | A%=&62:CALL&FFF1:A%=?X%:IFfs%<>10:OSCLI"FX143,18,"+STR$fs% | ||
| + | =A% | ||
| + | DEFFNfs:LOCALA%,E%,Y%:=(USR&FFDA)AND&FF | ||
==See Also== | ==See Also== | ||
| + | * [[OSWORD &72]] | ||
| + | * http://mdfs.net/Docs/Comp/BBC/Osword/Osword62 | ||
* http://mdfs.net/Docs/Comp/BBC/Oswords | * http://mdfs.net/Docs/Comp/BBC/Oswords | ||
[[User:Jgharston|Jgharston]] 14:00, 26 May 2009 (UTC) | [[User:Jgharston|Jgharston]] 14:00, 26 May 2009 (UTC) | ||
Revision as of 00:25, 18 March 2014
OSWORD &62 (98 ) - Access LVROM controller
Specification
Same format as ADFS call &72 (114)
On entry:
XY?0 = 0, returned result
XY!1 = data address
XY?5 = command
XY?6 = drive number in b5-b7, sector b16-b20 in b0-b4
XY?7 = sector number b8-b15
XY?8 = sector number b0-b7
XY?9 = number of sectors or 0
XY?10 = 0
XY!11 = data length if X%?9=0
This is a standard SCSI command block. The drive number in XY?6 is ORed with the current drive. If VFS is not selected when the call is made, VFS is selected. Consequently, any code that calls OSWORD &62 must remember the current filing system and restore it afterwards. In practice it is easier to select VFS before calling OSWORD &62.
Commands
&00=Test drive ready &01=Seek track 0 &03=Request status &08=Read data &0B=Seek track &1B=Stop/Start drive; stop if XY?9=0, start if XY?9=1 &C8=Read F-code result from LVDOS &CA=Transmit F-code to LVDOS
Results
&00=Ok &02=Drive door open &03=Media error, eg disk dirty &05=Bad SCSI command &04=Not ready &40=Write protected &48=CRC error &50=Sector not found &60=Bad command &61=Bad address &63=Volume error &65=Bad drive &6F=Abort
The result byte can be preloaded with a value to return if no OSWORD &62 routine exists. For instance, preloading the result with &00 makes all such failed calls appear to succeed, preloading with &50 makes all calls appear to return 'Sector not found'.
Coding
The following routine can be used to perform an OSWORD &62 call. It requires X%=>15-byte control block, Y%=X%DIV256.
DEFFNlvfs(cmd%,addr%,num%,sect%,drv%):LOCALfs% fs%=FNfs:IFfs%<>10:*FX143,18,10 X%?0=0:X%!1=addr%:X%?5=cmd%:X%?6=drv%*32+((sect%AND&1F0000)DIV65536) X%?7=((sect%AND&FF00)DIV256):X%?8=sect%:X%!9=0:X%!11=num% A%=&62:CALL&FFF1:A%=?X%:IFfs%<>10:OSCLI"FX143,18,"+STR$fs% =A% DEFFNfs:LOCALA%,E%,Y%:=(USR&FFDA)AND&FF
See Also
Jgharston 14:00, 26 May 2009 (UTC)
